Mikuni TDMR, got them :)
Moderators: trixynut, Mincehead, dicky, phuk72, Jak, Kevtrx849
- Rane850
- TRX-Enthusiast
- Posts: 69
- Joined: Wed Jan 21, 2009 1:26 pm
- Location: Finland
Mikuni TDMR, got them :)
Hi, I found myself a used TDMR 40 kit. It is a fully kit from Topham Germany. But I noticed that there is not spring and lever for accelerator pump in place? Previous owener has not removed it and he said that there was no hesitation and his TRX pulled like hell until it lost con rod bearing.
Anybody noticed this in other carbs, has it something to do with TUV- regulations ??
I cannot attach pic.
Anybody noticed this in other carbs, has it something to do with TUV- regulations ??
I cannot attach pic.
TRX850 bubum bubum - 96 and 98
XT500 -80 bum bum bum
XT500 -80 bum bum bum
- Rane850
- TRX-Enthusiast
- Posts: 69
- Joined: Wed Jan 21, 2009 1:26 pm
- Location: Finland
Re: Mikuni TDMR, got them :)
Anybody know what cables Topham has used, originals are too long.
TRX850 bubum bubum - 96 and 98
XT500 -80 bum bum bum
XT500 -80 bum bum bum
- Killerwhale
- Site Sponsor
- Posts: 3797
- Joined: Tue Aug 22, 2006 8:41 am
- Location: GBG/Sweden
- Contact:
Re: Mikuni TDMR, got them :)
First time i cut my originals and put new stopscrews on them....second time i bought cables on here from a member but they where for high bars so also to long....now i have high bars so perfect (not that it answered your Q though, but you can cut the standards to length)Rane850 wrote:Anybody know what cables Topham has used, originals are too long.
- Tarwetijger
- TRX-Enthusiast
- Posts: 1537
- Joined: Tue May 15, 2007 9:31 am
- Location: Netherlands, Assen
- Contact:
Re: Mikuni TDMR, got them :)
Partnr. from topham is TMP40/Y01 and cost 72,27 Euro (4 years ago). Overall length of outside cable incl. adjusting screws is 78cm.
I took the KRS-001 kit from topham as these are about 90 cm long, and I have a spare set.
So, if you prefer longer cables I might be able to help you.
I took the KRS-001 kit from topham as these are about 90 cm long, and I have a spare set.
So, if you prefer longer cables I might be able to help you.
- PrfctChaos
- TRX-Enthusiast
- Posts: 73
- Joined: Wed Nov 06, 2013 2:54 am
- Location: Perth, Australia
Re: Mikuni TDMR, got them :)
Universal throttle cable sets are cheap as chips. I used that and cut to length to suit the TDMR's. Fit-up, cut, solder, DONE.
1996 TRX, Front end from a 2006 GSXR 750, Seat off a 2012 Triumph street triple. TDMR carbs, Laser cans, Perreli Rosso Supercorsas.
- Rane850
- TRX-Enthusiast
- Posts: 69
- Joined: Wed Jan 21, 2009 1:26 pm
- Location: Finland
Re: Mikuni TDMR, got them :)
Thank you to all of you for tips. Now they are on place and I dont wonder why earlier owner broke his motor
What a nice pull in all rpm's. Only things are that no more need to go to city center as just small twist of wrist kicks so hard and during engine braking exhausts "talk" quite a lot. (should try to adjust idle mixture).
What a nice pull in all rpm's. Only things are that no more need to go to city center as just small twist of wrist kicks so hard and during engine braking exhausts "talk" quite a lot. (should try to adjust idle mixture).
TRX850 bubum bubum - 96 and 98
XT500 -80 bum bum bum
XT500 -80 bum bum bum
-
- Site Sponsor
- Posts: 6809
- Joined: Thu Aug 28, 2008 9:19 am
- Location: Brisbane,Australia
Re: Mikuni TDMR, got them :)
TDMR’s run the TPS on the RHS which means your tps map % will run back to front from 100% throttle to 0* ( reading voltage from 5v to 0v ).
You need to cut the 2 wires to the tps put in 2 covered bullet connectors so you can reverse the wiring.
If you ever go back to std carbies or fcr’s just unplug and swap them back.
You need to cut the 2 wires to the tps put in 2 covered bullet connectors so you can reverse the wiring.
If you ever go back to std carbies or fcr’s just unplug and swap them back.
laughter is the best medicine
- Tarwetijger
- TRX-Enthusiast
- Posts: 1537
- Joined: Tue May 15, 2007 9:31 am
- Location: Netherlands, Assen
- Contact:
Re: Mikuni TDMR, got them :)
I forgot about that! But no need to cut wires, you can swap the wiring in the connector to the TPS.cobbadiggabuddyblooo wrote:TDMR’s run the TPS on the RHS which means your tps map % will run back to front from 100% throttle to 0* ( reading voltage from 5v to 0v ).
You need to cut the 2 wires to the tps put in 2 covered bullet connectors so you can reverse the wiring.
If you ever go back to std carbies or fcr’s just unplug and swap them back.
It's a little fiddling though.
- Rane850
- TRX-Enthusiast
- Posts: 69
- Joined: Wed Jan 21, 2009 1:26 pm
- Location: Finland
Re: Mikuni TDMR, got them :)
Yes I did that mod. Topham has instructions in their web page.
TRX850 bubum bubum - 96 and 98
XT500 -80 bum bum bum
XT500 -80 bum bum bum